I made an 8 outlet box with relays connected to each outlet (might post a how to). That’s connected to a Pi via GPIO.

The Pi runs PiKVM, but also has a service that:

• Checks if the router can be pinged
• Checks if the internet can be pinged
• Checks if the router webUI is up

If any of those fail, it toggles the plugs for modem and router.

I run OpnSense on a 5V miniPC. I have a second one and will be setting up CARP, too.

Note: Cellular backup is more involved, but a separate Cellular inbound might not be. I’ve considered putting one on the Pi above.

If my lab goes down, it sucks, but that’s it. I have no critical service running there.

I have some recoverability, but it requires for the main router to run. If it isn’t running it’s either a HW failure, which I will not fix remotely anyway or power is down. In which case, not much I can do about it neither.

I have router with OpenWRT with Wireguard and main server (NUC) on a smart plug. If the router runs and server is mishaving to the point where I cannot reboot it, I can power cycle it via the smart plug connected to the router.

You mentioned your brother lives 30mins away - well put some tiny server in his house. Having everything at your home is not build for redundancy at all. That’s just the risk management, if you absolutely need access to your server, then 1 site is not going to cut it.

Redundancy. I have two independent firewalls, each separately routing traffic out through two totally independent multi-homed network connections (one cable, one DSL, please god somebody give me fiber someday) that both firewalls have access to. For awhile was thinking of replacing the DSL with starlink until Elon turned out to be such a pile of nazi garbage, so for now DSL remains the backup link.

To make things as transparent as possible, the firewalls manage their IPs with CARP. Obviously there’s no way to have a single public IP that ports itself magically from one ISP to another, but on the LAN side it works great and on the WAN side it at least smooths out a lot of possible failure scenarios. Some useful discussions of this setup are here.

For me I’d just say oh well, gotta fix it when I’m home again.

Otherwise I’d probably write some script on the server, which reboots my router when the server either doesn’t have internet anymore or can’t ping itself.

If you expect it to be flaky you could get one of those old school mechanical time switches with the clicky pegs (or a more modern digital equivalent) and just have it set to power down for 1 click, normally 15 mins, at 4am or whenever suits you - minimally technically complicated and guaranteed stability through planned instability!

I buy better gear that doesn’t regularly require a reboot

My mikrotik has not NEEDED a reboot ever, except when I run upgrades. Everything is set up to auto recover when disconnects happen, and power up properly if there’s an extended power failure that causes UPS shutdowns.

I will never understand why people think rebooting their router regularly is a normal thing. That just means your gear or setup is crap.

It didn’t happen in more than 5 years…

For critical equipment you need to spend the extra dollar to minimize this kind of stuff

On holiday, I’ll turn on my router’s auto-reboot option to reboot daily.

I’ve got one of those KeepConnect smart plugs which monitors a few different external servers and their own cloud, and automatically power cycles its outlet if things don’t work. They’ve damn near doubled in price since I’ve bought mine but it does work very well for me. Annual fee is reasonable too.

I could build something similar but I have too many projects as it is, and I feel I’d be fiddling with it endlessly just because I can. This is literally set and forget and in the last 2y it’s cycled the outlet 48 times, most of them in the middle of the night, presumably with my cable provider maintenance windows.

I had a 4G modem with a web interface many years ago. It was flaky and would often hang. I just had a raspberry pi on my network pinging some known address, if it failed for long enough it’d replay the commands to restart the web interface.

If I’d have the same problem today I’d probably have home assistant power cycle the router with a smart plug.

You have to say what your installation is like. If it’s typical consumer cable modem crap that locks up and needs a power cycle now and then, the simplest approach might just be to add a remote power cycle mechanism:

https://www.adafruit.com/product/2935

isn’t the cheapest but it’s nicely packaged. That’s just a switchable power strip, so yes you’d need some kind of cellular internet or meshtastic or something to operate it if you want to do it manually, or else just have something automatically power cycle the router if it notices the internet down for more than 3 minutes or something.

In the more serious case where your box is at a data center, you generally open a ticket with the data center and ask them to reboot the box (“remote hands”). Sometimes they will do that for free, other times they charge you.

0 4   *   *   *    /usr/sbin/reboot

Adjust interval as needed.

Or if you want something a bit faster:

#!/bin/sh

NAME="$0"

logger_cmd () {
  echo $@
  logger -p daemon.info -t "$NAME[$$]" $@
}

if ! which ncat 1>/dev/null
then
  logger_cmd "ncat not found, installing..."
  opkg update && opkg install ncat
fi

chk_conn () {
  echo "Checking connectivity to $@"
  if ncat --send-only --recv-only -w 334ms $@ 2>/dev/null; then
    return 0
  fi

  logger_cmd "Cannot reach $@"
  return 1
}

restart_network_iface() {
    # TODO: Don't restart every minute

    COOLDOWN_LOCK=/tmp/internet-connectivity-watchcat.tmp
    COOLDOWN_SECONDS=300

    cooldown_time_end=$(cat $COOLDOWN_LOCK || echo 0)

    time_now="$(cat /proc/uptime)"
    time_now="${time_now%%.*}"

    cooldown_time_left=$((cooldown_time_end - time_now))

    if [ "$cooldown_time_left" -lt "1" ]
    then
        logger_cmd "Restarting network interface: \"$1\"."
        ifdown "$1"
        ifup "$1"

        cooldown_time_end=$((time_now + COOLDOWN_SECONDS))
        echo $cooldown_time_end > $COOLDOWN_LOCK
    else
        logger_cmd "Skipping interface \"$1\" restart due to cooldown. Cooldown left: $cooldown_time_left seconds"
    fi
}


logger_cmd "Checking internet connectivity..."

if   chk_conn google.com 443 \
  || chk_conn amazon.com 443 \
  || chk_conn facebook.com 443 \
  || chk_conn cloudflare.com 443 \
  || chk_conn telekom.de 443
then
  logger_cmd "Connected to internet."
else
  logger_cmd  "Not connected to internet."
  restart_network_iface "$1"
fi

In restart_network_iface use /usr/sbin/reboot instead of interface up/down and run the script every few minutes via cron or systemd timer. This was written for OpenWrt so if you use that you can use it as-is. For other systems you’d also have to adjust the logger_cmd.

You can place that on another machine and send a signal to a smart plug instead if you’re worried of a locked up / frozen router. That said if your router freezes like that, you should probably change it and you should be able to run this script on it.

if the primary internet router goes offline but the internet isn’t out (ie a router reboot would fix the problem)

Maybe you just need to give it a simple power cycle remotely? There are devices that do that sort of thing, I have a Digital Loggers Web Power Switch Pro that I’ve used on-and-off over the years for this purpose.

https://www.digital-loggers.com/

At one point I had to relocate for half a year while needing to remote access a slightly unstable desktop that wouldn’t always reboot cleanly and get stuck at the BIOS, it sometimes needed a couple of power cycles to come back online. The Power Switch was perfect for that, I’d log into it remotely and power cycle anything that was plugged into it.

It should work for routers too e.g. it can automatically power cycle something plugged into it based on different conditions like maybe it stops responding to pings or whatever. Or I guess if you had multiple IPs / multiple internet connections the switch itself can stay online and accessed remotely without needing to schedule anything automatic.

Pretty sure there are more pro-level (and more expensive) types of devices to do this sort of thing if you look around

Its my house so ill just walk over and fix it.

If im out, nothing is too important enough that it cant be fixed in a couple of days.

I’ve moved my instant messenger onto a VPS and that has a good uptime. And I’m somewhat okay if my Nextcloud and calendars don’t sync. Most important data is synced anyway.

Other than that I’ve called my ISP a bunch of times to give me a new router, they refused, I canceled the subscription and made a new one and got a new router. And that one is better. And in doubt I’ll call a family member.